Flat Fan Spraying

Flat Fan spray nozzles produce a fan-shaped pattern, that is mainly produced by two methods; an angled cut or groove, with which the water is hydraulically driven to produce the flat pattern, or via a sloping deflection face with uses the slope to drive the spray pattern.

These nozzles produce a thin, flat sheet of liquid that expands outward from the nozzle typically in a ‘V-shaped’ pattern. A thin line of liquid is produced when the spray intersects a surface. As the liquid is concentrated into a smaller area, the impact force from fan nozzles can be greater than that produced from a full or hollow cone nozzle.

  • BJ-Low-Flow-Sprayer-Nozzles-min

    Nozzle Features

    • Three-piece construction
    • Flow rates from 0.084 L/Min to 101 L/Min
    • Interchangeable spray tips
    • Relatively coarse atomisation
    • Uniform distribution with tapered edges for use in overlapping sprays
    Flatfan_50_80          
  • BJH-Flat-Fan-Nozzles-with-Tungsten-Carbide-Inserts-min

    Nozzle Features

    • Interchangeable spray tips
    • Flow rates from 0.048 L/Min to 16.6 L/Min
    • Tungsten carbide orifice inserts for maximum wear resistance and service life
    • Relatively coarse atomisation
    • Uniform distribution with tapered edges for use in overlapping sprays
    Flatfan_80-min

  • EZFF-EZ-Flat-Fan-Quick-Change-Spray-Nozzles-min

    Nozzle Features

    • EZ FF Flow rates from 0.051 L/Min to 61.1 L/Min
    • Three-part nozzle, base, gasket and interchangeable tip
    • Exclusive ramped engagement for efficient, automatic alignment
    • Threaded adaptors will accommodate other standard BETE nozzles. Shut-off plugs are also available
    • Sanitary EZs are available with weld connection and no knurling
    Flatfan_145_50-min
  • EZNF-EZ-Flat-Fan-Quick-Change-Spray-Nozzles--min

    Nozzle Features

    • EZ NF Flow rates from 0.016 to 121 L/Min
    • Three-part nozzle, base, gasket and interchangeable tip
    • Exclusive ramped engagement for efficient, automatic alignment
    • Threaded adaptors will accommodate other standard BETE nozzles. Shut-off plugs are also available
    • Sanitary EZs are available with weld connection and no knurling
    Flatfan_145_50-min
  • EZSPN-EZ-Flat-Fan-Quick-Change-Spray-Nozzles-min

    Nozzle Features

    • EZ SPN Flow rates from 1.25 L/Min to 125 L/Min
    • Three-part nozzle, base, gasket and interchangeable tip
    • Exclusive ramped engagement for efficient, automatic alignment
    • Threaded adaptors will accommodate other standard BETE nozzles. Shut-off plugs are also available
    • Sanitary EZs are available with weld connection and no knurling
    Flatfan_145_50-min
  • FF-Extra-Wide-Angle-Nozzles-min

    Nozzle Features

    • One-piece construction
    • Flow rates from 0.051 L/Min to 757 L/Min
    • Clog-resistant
    • 3/8″ FFs in Brass is available with UL approval
    • For FM-approved flat fan nozzles, see the AFF series
    • Extra-wide 145° spray angle
    • Medium-impact spray
    • Coarse atomisation
    Flatfan_145-min
  • HydroPulse®-Direct-Pressure-Spray-Nozzles-With-Air-Actuated-Shut-Off

    Key Features

    • The simple and maintenance-friendly design allows for disassembly, inspection/cleaning, and reassembly with basic hand tools
    • Two fluid ports are standard; a plug to seal the recirculation port is included.
    • Air Cylinder Pressure: Minimum: 30 psi; Maximum: 250 psi.
    • Operating Temperature Range: -15 °F to 400 °F. Nylon Mounting Hardware: 250 °F MA
    • Air Cylinder: Stainless Steel, Anodized Aluminum, PTFE, and Viton®
    • Fluid Seals: FDA-compliant Viton®
    • Air Cylinder: Single-acting spring extends type. Air pressure retracts the rod and allows flow through the nozzle. Removing air pressure extends the rod and seals the nozzle. Double-acting cylinder is available upon request.
    • Frequency Rating: Up to 180 cycles/minute, with an appropriate solenoid valve (Cv=0.08 minimum).

    Design Features

    • Provides a controlled intermittent liquid spray using only liquid pressure as the force for atomization.
    • Drip-free performance.
    • Pneumatically actuated for crisp on/off spray
    • Straight through porting for fluid recirculation

    Spray Characteristics

    • Relatively coarse atomization
    • Uniform distribution with tapered edges for use in overlapping sprays
  • NF_Standard_Fan-min

    Nozzle Features

    • One-piece construction
    • Flow rates from 0.16 L/Min to 2810 L/Min
    • No internal parts
    • High impact
    • Uniform distribution with tapered edges for overlapping sprays
    • Extra-wide angles available
    Flatfan_50-min
  • NFD-Dovetail-Flat-Fan-Nozzles-min

    Nozzle Features

    • Dovetail joint guarantees alignment of interchangeable tips
    • Flow rates from 0.15 L/Min to 358 L/Min
    • Tips offset 5° or 15° for overlapping spray patterns
    • The tapered overlapping spray provides uniform coverage
    • Male, female and welded connections
    Flatfan_45-min
  • NFH-Fan-Nozzles-with-Tungsten-Carbide-Inserts-min

    Nozzle Features

    • Tungsten carbide orifice inserts for maximum wear resistance and service life
    • Flow rates from 0.048 L/Min to 16.6 L/Min
    • Relatively coarse atomisation
    • Uniform distribution with tapered edges for use in overlapping sprays
    Flatfan_80-min          

  • NFS-Stubby-Flat-Fan-Nozzles-min

    Nozzle Features

    • Extremely short length for minimum projection and maximum clearance
    • Flow rates from 0.20 L/Min to 951 L/Min
    • Available in straight (parallel) threads only, NPSM and G
    • Requires gasket to seal the connection
    Fan45-and-90-min
  • NFV-High-Impact-Fan-Nozzles-With-Integral-Strainer-Option-min

    Nozzle Features

    • Low nozzle maintenance
    • Flow Rates from 0.15 L/Min to 49.85 L/Min
    • No internal parts
    • Optional removable strainer for easy cleaning
    • Uniform distribution
    Flatfan_50-min
  • SF_Snap_release_Nozzle_system-min

    Nozzle Features

    • Quick set-up system features special “Snap-in” tips
    • Flow rates from 1.61 L/Min to 75.6 L/Min
    • Double clamp base or adapter available for higher pressure operations
    • Quick set-up system can be provided with fan, hollow or full cone spray tips
    • Full 45° alignment of spray without tools
    Flatfan_50-min
  • SPN High impact_Narrow Fan Spray-min

    Nozzle Features

    • One-piece/heavy construction
    • Flow rates from 0.76 L/Min to 177 L/Min
    • Straight-through orifice minimizes clogging
    • Yields highest impact, narrow flat spray with least atomization
    • Spoon-shaped deflector surface efficiently forms a hard-driving spray
    Fan50_angle-min

Title